[Soekris] asking about voltage and temperature monitoring soekris net 4801

[komang adi]

Now, i have success found some of the voltage, but not all of them appear,
here is the output :
root at relay:/home/relay# sensors
pc87366-isa-6620
Adapter: ISA adapter
VCORE:       +0.00 V  (min =  +1.90 V, max =  +2.10 V)
VCC:         +0.00 V  (min =  +0.00 V, max =  +0.00 V)
VPWR:        +0.00 V  (min =  +5.93 V, max = +28.02 V)
+12V:        +0.00 V  (min = +11.02 V, max = +13.01 V)
-12V:       -60.06 V  (min = -13.10 V, max = -11.06 V)
GND:         +0.00 V  (min =  +0.00 V, max =  +0.00 V)
Vsb:         +6.03 V  (min =  +3.00 V, max =  +3.59 V)
Vdd:         +6.03 V  (min =  +3.00 V, max =  +3.59 V)
Vbat:        +0.00 V  (min =  +2.40 V, max =  +3.01 V)
AVdd:        +6.03 V  (min =  +3.00 V, max =  +3.59 V)
Temp:       -128.0 C  (low  =  +0.0 C, high = +70.0 C)
                      (crit = +85.0 C)
cpu0_vid:   +0.000 V

How i can to make all of them appear and make it show voltage and thermal
correctly? I have activated National Semiconductor kernel driver for voltage
and thermal monitoring. Thanks.

-komang

2008/5/23 Henrik Brix Andersen <henrik at brixandersen.dk>:

> On Thu, May 22, 2008 at 06:41:06PM +0800, komang adi wrote:
> > yes, i have seen that before. But, i'm using ubuntu for the OS. The
> program
> > at  http://phk/soekris/env4801/ using free besd. Can i just apply it for
> the
> > ubuntu? Thanks
>
> Not directly, no. A while back, I wrote a small howto for doing this
> under Linux:
>
>
> http://www.brixandersen.dk/papers/net4801/net4801.html#sect-kernel-temp-volt
>
> > 2008/5/22 Poul-Henning Kamp <phk at phk.freebsd.dk>:
> >
> > > In message <d3a276f0805220259h32836eaayd951b9ffbe7da0f9 at mail.gmail.com
> >,
> > > "koman
> > > g adi" writes:
> > >
> > > >i'm trying to monitor the condition of the voltage and temperature of
> the
> > > >soekris net4801 using lm-sensors, but i just find the link about that
> at
> > > >http://www.linuxvillage.ca/support/soekris4801.html#sensor_conf, but
> the
> > > >output just like this :
> > >
> > > Looks like the sensor subsystem is not properly turned on in the
> > >
> > > Check this program:
> > >        http://phk/soekris/env4801/
>
> Brix
>
> PS: Please avoid top posting :-)
> --
> Henrik Brix Andersen <henrik at brixandersen.dk>
>
> _______________________________________________
> Soekris-tech mailing list
> Soekris-tech at lists.soekris.com
> http://lists.soekris.com/mailman/listinfo/soekris-tech
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.soekris.com/pipermail/soekris-tech/attachments/20080526/320317ab/attachment.html