[Soekris] again: sis1, sis2 wont work after bios update

Thu Jul 22 21:08:42 UTC 2004

On Thu 2004.07.22 at 22:05 +0200, llx wrote:
> some days a (before beeing on the list) i wrote that the sis1 sis2 on my 4801 
> don't work any more after updating the bios from 1.22 to 1.24. i saw one reply 
> to my post suggesting me to use the GENERIC kernel (openbsd). if you look at 
> the dmesg from my post (12 july 2004) you can see that i am using generic. 
> the same installation worked befor the bios update but fails after the 
> update. i am constantly getting watchdog timeouts on the interfaces sis1 and 
> sis2. does anybody have any idea or do i have to throw my 4801 out of the 
> window? 

have you tried putting "up" in each /etc/hostname.sis{0,1,2} that is not
configured by default?

> unfortunately there's no 1.22 bios for download on the soekris server. 
> otherwise i would downgrade to 1.22. this was the bios version that was 
> installed when i bought it.
> 
> cheers
> 
> 
> the dmesg again:
> # dmesg (and more: )
> comBIOS ver. 1.24  20040312  Copyright (C) 2000-2004 Soekris Engineering.
> 
> net4801
> 
> 0128 Mbyte Memory                        CPU Geode 266 Mhz
> 
> Pri Mas  TOSHIBA MK4025GAS               LBA Xlt 1024-255-63  39070 Mbyte
> 
> PXE-M00: BootManage UNDI, PXE-2.0 (build 082)
> 
> Slot   Vend Dev  ClassRev Cmd  Stat CL LT HT  Base1    Base2   Int
> -------------------------------------------------------------------
> 0:00:0 1078 0001 06000000 0107 0280 00 00 00 00000000 00000000 00
> 0:06:0 100B 0020 02000000 0107 0290 00 3F 00 0000E101 A0000000 10
> 0:07:0 100B 0020 02000000 0107 8290 00 3F 00 0000E201 A0001000 10
> 0:08:0 100B 0020 02000000 0107 8290 00 3F 00 0000E301 C0002000 10
> 0:18:2 100B 0502 01018001 0005 0280 00 00 00 00000000 00000000 00
> 0:19:0 0E11 A0F8 0C031008 0117 0280 08 38 00 D0003000 00000000 11
> 
>  1 Seconds to automatic boot.   Press Ctrl-P for entering Monitor.
> Using Drive: 0 Partition: 3
> reading boot....
> probing: pc0 com0 com1 pci mem[639K 127M a20=on]
> disk: hd0+
> 
> >> OpenBSD/i386 BOOT 2.02
> 
> switching console to com0
> com0: changing speed to 19200 baud
> com0: change your terminal to match!
> com0: will change speed in 5 seconds....
> 
> com0: console is at 19200 baud
> boot>
> booting hd0a:/bsd: 4466548+838588 [58+204384+181909]=0x56da00
> entry point at 0x100120
> 
> [ using 386768 bytes of bsd ELF symbol table ]
> Copyright (c) 1982, 1986, 1989, 1991, 1993
>         The Regents of the University of California.  All rights reserved.
> Copyright (c) 1995-2003 OpenBSD. All rights reserved.  http://www.OpenBSD.org
> 
> OpenBSD 3.4-stable (GENERIC) #3: Thu Jun  3 01:31:54 CEST 2004
>     root at gate.corebounce.org:/usr/src/sys/arch/i386/compile/GENERIC
> cpu0: National Semiconductor Geode GX1 ("Geode by NSC" 586-class) 267 MHz
> cpu0: FPU,TSC,MSR,CX8,CMOV,MMX
> real mem  = 133804032 (130668K)
> avail mem = 118124544 (115356K)
> using 1658 buffers containing 6791168 bytes (6632K) of memory
> mainbus0 (root)
> bios0 at mainbus0: AT/286+(00) BIOS, date 20/40/12, BIOS32 rev. 0 @ 0xf7840
> pcibios0 at bios0: rev. 2.0 @ 0xf0000/0x10000
> pcibios0: pcibios_get_intr_routing - function not supported
> pcibios0: PCI IRQ Routing information unavailable.
> pcibios0: PCI bus #0 is the last bus
> bios0: ROM list: 0xc8000/0xa000
> pci0 at mainbus0 bus 0: configuration mode 1 (bios)
> pchb0 at pci0 dev 0 function 0 "Cyrix GXm Host-PCI" rev 0x00
> sis0 at pci0 dev 6 function 0 "NS DP83815 10/100" rev 0x00: irq 10 address
> 00:00
> 
> :24:c1:52:64
> 
> nsphyter0 at sis0 phy 0: DP83815 10/100 integrated, rev. 1
> sis1 at pci0 dev 7 function 0 "NS DP83815 10/100" rev 0x00: irq 10 address
> 00:00
> 
> :24:c1:52:65
> 
> nsphyter1 at sis1 phy 0: DP83815 10/100 integrated, rev. 1
> sis2 at pci0 dev 8 function 0 "NS DP83815 10/100" rev 0x00: irq 10 address
> 00:00
> 
> :24:c1:52:66
> 
> nsphyter2 at sis2 phy 0: DP83815 10/100 integrated, rev. 1
> pcib0 at pci0 dev 18 function 0 "NS SC1100 ISA" rev 0x00
> "NS SC1100 SMI/ACPI" rev 0x00 at pci0 dev 18 function 1 not configured
> pciide0 at pci0 dev 18 function 2 "NS SCx200 IDE" rev 0x01: DMA
>  (unsupported), c
> hannel 0 wired to compatibility, channel 1 wired to compatibility
> pciide0: channel 0 ignored (other hardware responding at addresses)
> pciide0: channel 1 ignored (not responding; disabled or no drives?)
> "NS SC1100 X-Bus" rev 0x00 at pci0 dev 18 function 5 not configured
> ohci0 at pci0 dev 19 function 0 "Compaq USB OpenHost" rev 0x08: irq 11, OHCI
> ver
> sion 1.0, legacy support
> usb0 at ohci0: USB revision 1.0
> uhub0 at usb0
> uhub0: Compaq OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub0: 3 ports with 3 removable, self powered
> isa0 at pcib0
> isadma0 at isa0
> pckbc0 at isa0 port 0x60/5
> pckbd0 at pckbc0 (kbd slot)
> pckbc0: using irq 1 for kbd slot
> wskbd0 at pckbd0: console keyboard
> wdc0 at isa0 port 0x1f0/8 irq 14
> wd0 at wdc0 channel 0 drive 0: <TOSHIBA MK4025GAS>
> wd0: 16-sector PIO, LBA, 38154MB, 16383 cyl, 16 head, 63 sec, 78140160
>  sectors wd0(wdc0:0:0): using BIOS timings
> pcppi0 at isa0 port 0x61
> midi0 at pcppi0: <PC speaker>
> sysbeep0 at pcppi0
> npx0 at isa0 port 0xf0/16: using exception 16
> pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
> pccom0: console
> pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
> biomask 4800 netmask 4c00 ttymask 4c02
> pctr: user-level cycle counter enabled
> dkcsum: wd0 matched BIOS disk 80
> root on wd0a
> rootdev=0x0 rrootdev=0x300 rawdev=0x302
> Automatic boot in progress: starting file system checks.
> /dev/rwd0a: file system is clean; not checking
> /dev/rwd0e: file system is clean; not checking
> /dev/rwd0f: file system is clean; not checking
> /dev/rwd0d: file system is clean; not checking
> setting tty flags
> net.inet.ip.forwarding: 0 -> 1
> starting network
> writing to routing socket: File exists
> starting system logger
> starting rpc daemons:.
> sis1: watchdog timeout
> savecore: no core dump
> checking quotas: done.
> building ps databases: kvm dev.
> clearing /tmp
> starting pre-securelevel daemons:.
> setting kernel security level: kern.securelevel: 0 -> 1
> preserving editor files
> creating runtime link editor directory cache.
> starting network daemons: rtsoldusage: rtsold [-adDfm1] interfaces...
> usage: rtsold [-dDfm1] -a
>  sendmail inetd sshdsis1: watchdog timeout
> .
> starting local daemons:.
> _______________________________________________
> Soekris-tech mailing list
> Soekris-tech at lists.soekris.com
> http://lists.soekris.com/mailman/listinfo/soekris-tech