[Soekris] again: sis1, sis2 wont work after bios update

[llx]

some days a (before beeing on the list) i wrote that the sis1 sis2 on my 4801 
don't work any more after updating the bios from 1.22 to 1.24. i saw one reply 
to my post suggesting me to use the GENERIC kernel (openbsd). if you look at 
the dmesg from my post (12 july 2004) you can see that i am using generic. 
the same installation worked befor the bios update but fails after the 
update. i am constantly getting watchdog timeouts on the interfaces sis1 and 
sis2. does anybody have any idea or do i have to throw my 4801 out of the 
window? 

unfortunately there's no 1.22 bios for download on the soekris server. 
otherwise i would downgrade to 1.22. this was the bios version that was 
installed when i bought it.

cheers


the dmesg again:
# dmesg (and more: )
comBIOS ver. 1.24  20040312  Copyright (C) 2000-2004 Soekris Engineering.

net4801

0128 Mbyte Memory                        CPU Geode 266 Mhz

Pri Mas  TOSHIBA MK4025GAS               LBA Xlt 1024-255-63  39070 Mbyte

PXE-M00: BootManage UNDI, PXE-2.0 (build 082)

Slot   Vend Dev  ClassRev Cmd  Stat CL LT HT  Base1    Base2   Int
-------------------------------------------------------------------
0:00:0 1078 0001 06000000 0107 0280 00 00 00 00000000 00000000 00
0:06:0 100B 0020 02000000 0107 0290 00 3F 00 0000E101 A0000000 10
0:07:0 100B 0020 02000000 0107 8290 00 3F 00 0000E201 A0001000 10
0:08:0 100B 0020 02000000 0107 8290 00 3F 00 0000E301 C0002000 10
0:18:2 100B 0502 01018001 0005 0280 00 00 00 00000000 00000000 00
0:19:0 0E11 A0F8 0C031008 0117 0280 08 38 00 D0003000 00000000 11

 1 Seconds to automatic boot.   Press Ctrl-P for entering Monitor.
Using Drive: 0 Partition: 3
reading boot....
probing: pc0 com0 com1 pci mem[639K 127M a20=on]
disk: hd0+

>> OpenBSD/i386 BOOT 2.02

switching console to com0
com0: changing speed to 19200 baud
com0: change your terminal to match!
com0: will change speed in 5 seconds....

com0: console is at 19200 baud
boot>
booting hd0a:/bsd: 4466548+838588 [58+204384+181909]=0x56da00
entry point at 0x100120

[ using 386768 bytes of bsd ELF symbol table ]
Copyright (c) 1982, 1986, 1989, 1991, 1993
        The Regents of the University of California.  All rights reserved.
Copyright (c) 1995-2003 OpenBSD. All rights reserved.  http://www.OpenBSD.org

OpenBSD 3.4-stable (GENERIC) #3: Thu Jun  3 01:31:54 CEST 2004
    root at gate.corebounce.org:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: National Semiconductor Geode GX1 ("Geode by NSC" 586-class) 267 MHz
cpu0: FPU,TSC,MSR,CX8,CMOV,MMX
real mem  = 133804032 (130668K)
avail mem = 118124544 (115356K)
using 1658 buffers containing 6791168 bytes (6632K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(00) BIOS, date 20/40/12, BIOS32 rev. 0 @ 0xf7840
pcibios0 at bios0: rev. 2.0 @ 0xf0000/0x10000
pcibios0: pcibios_get_intr_routing - function not supported
pcibios0: PCI IRQ Routing information unavailable.
pcibios0: PCI bus #0 is the last bus
bios0: ROM list: 0xc8000/0xa000
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "Cyrix GXm Host-PCI" rev 0x00
sis0 at pci0 dev 6 function 0 "NS DP83815 10/100" rev 0x00: irq 10 address
00:00

:24:c1:52:64

nsphyter0 at sis0 phy 0: DP83815 10/100 integrated, rev. 1
sis1 at pci0 dev 7 function 0 "NS DP83815 10/100" rev 0x00: irq 10 address
00:00

:24:c1:52:65

nsphyter1 at sis1 phy 0: DP83815 10/100 integrated, rev. 1
sis2 at pci0 dev 8 function 0 "NS DP83815 10/100" rev 0x00: irq 10 address
00:00

:24:c1:52:66

nsphyter2 at sis2 phy 0: DP83815 10/100 integrated, rev. 1
pcib0 at pci0 dev 18 function 0 "NS SC1100 ISA" rev 0x00
"NS SC1100 SMI/ACPI" rev 0x00 at pci0 dev 18 function 1 not configured
pciide0 at pci0 dev 18 function 2 "NS SCx200 IDE" rev 0x01: DMA
 (unsupported), c
hannel 0 wired to compatibility, channel 1 wired to compatibility
pciide0: channel 0 ignored (other hardware responding at addresses)
pciide0: channel 1 ignored (not responding; disabled or no drives?)
"NS SC1100 X-Bus" rev 0x00 at pci0 dev 18 function 5 not configured
ohci0 at pci0 dev 19 function 0 "Compaq USB OpenHost" rev 0x08: irq 11, OHCI
ver
sion 1.0, legacy support
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: Compaq OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
wdc0 at isa0 port 0x1f0/8 irq 14
wd0 at wdc0 channel 0 drive 0: <TOSHIBA MK4025GAS>
wd0: 16-sector PIO, LBA, 38154MB, 16383 cyl, 16 head, 63 sec, 78140160
 sectors wd0(wdc0:0:0): using BIOS timings
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
sysbeep0 at pcppi0
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom0: console
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
biomask 4800 netmask 4c00 ttymask 4c02
pctr: user-level cycle counter enabled
dkcsum: wd0 matched BIOS disk 80
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302
Automatic boot in progress: starting file system checks.
/dev/rwd0a: file system is clean; not checking
/dev/rwd0e: file system is clean; not checking
/dev/rwd0f: file system is clean; not checking
/dev/rwd0d: file system is clean; not checking
setting tty flags
net.inet.ip.forwarding: 0 -> 1
starting network
writing to routing socket: File exists
starting system logger
starting rpc daemons:.
sis1: watchdog timeout
savecore: no core dump
checking quotas: done.
building ps databases: kvm dev.
clearing /tmp
starting pre-securelevel daemons:.
setting kernel security level: kern.securelevel: 0 -> 1
preserving editor files
creating runtime link editor directory cache.
starting network daemons: rtsoldusage: rtsold [-adDfm1] interfaces...
usage: rtsold [-dDfm1] -a
 sendmail inetd sshdsis1: watchdog timeout
.
starting local daemons:.